ASTM Dpdf – Download as PDF File .pdf), Text File .txt) or read online. – Download as PDF File .pdf), Text File .txt) or read online. ASTM Dpdf. November 29, | Author: Nok Chan | Category: Distillation, Thermometer, Electric Heating, Liquids, Temperature.

Author: Nakazahn Malazil
Country: Thailand
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 14 April 2018
Pages: 182
PDF File Size: 12.23 Mb
ePub File Size: 18.62 Mb
ISBN: 936-8-23423-981-4
Downloads: 65162
Price: Free* [*Free Regsitration Required]
Uploader: Faejar

ASTM D1078.pdf

When dd1078 decomposition is encountered, the rapid evolution of vapor and heavy fumes is usually followed by a gradual decrease in the distillation temperature.

A number in parentheses indicates the year of last reapproval. Size px x x x x For low-boiling materials, cool the heating unit to room temperature before starting the test. Thank you for interesting in our services.

Measure the volume and record it as residue. If yields are not obtained within these limits, repeat the test. D — 01 Designation: Confirmation of the calibration of these temperature sensors shall be done at regular intervals.

ASTM Dpdf – Free Download PDF

IBP 50 75 r 0. Originally published as D — 49 T. A small but statistically significant bias adtm indicated for the automatic and manual D dry point DP. Organic liquids are used as solvents in many chemical processes. Center the thermometer into the neck of the flask through a tight-fitting cork stopper so that the upper end of the contraction chamber or bulb if Thermometer 2C or IP thermometer 62C is used is level with the lower side of the vapor tube at its junction with the neck of the flask.

NOTE 4—For low-boiling materials, cool the apparatus to room temperature before starting the test. When peroxide formation is likely because of chemical type or length of storage, the material should be analyzed for peroxides See Test Method E The qstm bias if any are only for the samples studied and may not be necessarily applicable to other samples.


We need your help to maintenance this website. Organic liquids are used as solvents in many chemical processes.

Historical Version s – view previous versions of standard. The temperature of the mercury in the thermometer is equilibrated with that of the refluxing liquid before the distillate is taken over. For narrow-boiling hydrocarbon materials, the value of K may be assumed as 0.

Your comments will receive careful consideration at a meeting of the responsible technical committee,1 which you may attend. As the relative volatility, residual matter and recovery capability affect the efficiency of these processes, this test method is useful in manufacturing control.

Specific 3 D factors conducive to superheating are as follows, and should be avoided: Place the receiver, without drying, at the outlet of the condenser tube in such a position that the condenser tube extends into the graduate at least 25 mm but does not extend below the mL mark.

This test method provides a method of measurement of distillation range of volatile organic liquids.

A These thermometers have more temperature lag than the other thermometers listed herein and are not satisfactory for use with narrow-boiling range liquids. We need your help! Significance and Use 5. Ten laboratories did automatic D distillation, and five laboratories did manual D distillation.

Caution should be taken when handling mercury and mercury-containing products. The flask is then prepared for use by washing with water, rinsing with acetone, and drying.


HDA 620: Distillation Analyzer

Therefore, this test method provides a test procedure for assessing compliance with a specification. If a dry point is not obtained that is, if active decomposition should occur before the dry point is reached, as evidenced by a rapid evolution of vapor or heavy fumes; or if there is liquid remaining on the bottom of the flask when the maximum temperature is observed on the distillation thermometerrecord this fact.

No other units sstm measurement are included in this standard. As the relative f1078, residual matter and recovery capability affect the efficiency of these processes, this test method r1078 useful in manufacturing control.

In the operation of the distillation apparatus, use a suitable catch pan and shielding to contain spilled liquid in the event of accidental breakage of the distillation flask.

This can be accomplished potentiometrically by the use of standard precision resistance, depending on the type of probe. Mercury, or its vapor, may be hazardous to health and corrosive to materials. It was found that the precision is dependent sstm the boiling point temperature. Table 6 gives a summary of the relative bias observed for the samples used in the study. These should be used only after they have been s1078 to give results comparable to those obtained when using gas heat.

Boiling temperatures observed on a partial immersion thermometer are corrected to standard atmospheric pressure to give true boiling temperatures.